IT’s ITT

ITT is Internal Turbine Temperature. This is the system that indicates to the pilot the operating temperature of the engine. So, what is the ITT system?

The PT6 has several stations throughout. Various things are measured at these stations. You may be familiar with P3 air. The interpretation of that is the air pressure at station three. The ITT system is the same way. You may have heard me, or others refer to it as T5. Yes, you guessed it, ITT is measuring the temperature at station five. Station five is located right between the compressor turbine and the power turbine. That is the temperature that we want to measure.

The T5 system consists of either 8 or 10 thermocouples that extend into the airstream between the turbines. The thermocouples are connected in parallel with a bus bar. A wiring harness is connected to the bus bar and then comes to the outside of the engine. Before the signal goes to the gauge, a probe is also attached in parallel, commonly known as the trim stick. The trim stick adjusts the reading in the cockpit a prescribed amount. This amount is determined on the test cell run of the engine, where a formula that includes the temperatures of the inlet and exhaust is used to determine the trim value. The trim stick provides a specific bias to the indication to compensate for sampling errors. This is critical to ensure that the internal critical component's temperatures are within the acceptable range. The trim stick cannot be adjusted or changed in the field without consultation from Pratt & Whitney Canada engineering. It can be replaced with the same class if found to be faulty.

The thermocouples consist of alumel and chromel portions. The two metals are joined together and send an electrical signal when they get hot. This is the signal that goes to the gauge the pilot is reading. If you need to identify the difference between the alumel and chromel sides of the wire harness, they are different sizes. The alumel connections are bigger, I always remember them as BIG AL, and now you will too.

Why am I bringing all of this up? I have received some calls recently regarding intermittent or fluctuating ITT readings. There are testing instructions for the whole system in the maintenance manual. You can test it as a complete unit. You can also split the engine at the C-flange and test the individual components. When advising people on the process, I always start with a check of the ITT gauge. Remember to set your test equipment, considering the lead between the engine and the gauge. You can then induce an electrical signal with your tester and compare the reading to the reading in the cockpit.

Once the gauge is determined to be good or replaced, we test the engine components. We test for resistance and continuity. The issue then becomes, how do we trace an intermittent problem? Most of the time, what I have found is that there is a "disconnect" somewhere in the system. This can be chaffing on the ITT wire harness or a broken leg on the bus bar; I have even found a broken bolt before. Sometimes there is insulation that becomes brittle over time and can allow a short in the system. These can only be thoroughly checked by splitting the engine. Sometimes, you might have to "wiggle" the components to find the issue. Once the issue is located, it can easily be handled by component repair or replacement.

A couple of extras. Humidity can cause erroneous readings. Be sure to follow the manuals when dealing with ITT components, as sometimes it will have you heat them for both checking and removing moisture. Lastly, handle the complete system with care. When reinstalling the power section, ensure the wire harness is tucked away as much as possible. Don't bang the bus bar as the engine halves go together.

Intermittent problems can be the worst when it comes to troubleshooting. If you take a step-by-step approach with some information and assistance, you can almost always find the problem. As always, reference the manuals and ask for help. We are all in this together.

Robert Craymer has worked on PT6A engines and PT6A-powered aircraft for the past three decades, including the last 25+ years at Covington Aircraft. As a licensed A&P mechanic, Robert has held every job in an engine overhaul shop and has been an instructor of PT6A Maintenance and Familiarization courses for pilots and mechanics. Robert has been elected to the NAAA board as the Allied-Propulsion Board Member. Robert can be reached at [email protected] or 662-910-9899. Visit us at covingtonaircraft.com.

[ufc-fb-comments]

Commercial manned and unmanned aerial applicators invest time, resources, and their livelihood into their business to be licensed, experienced and professional. To ensure the professionalism of aerial application, report unlicensed operations. Find out more at: news.agaviation.org/naaa/issues/2023-06-01/1.html ... See MoreSee Less

Comment on Facebook

Can someone tell me how we are supposed to identify someone standing on the road as unlicensed? Also, I see the FAA turning a blind eye to this, so who would you report it to that's really going to do something about it.

We have a serious problem with illegal drones in South Africa. This last season I had 5 encounters with drones spraying fields adjacent to the fields I was spraying. Our CAA will not do anything about it until there is an accident. These things weigh 90 kg, so will probably bring an aircraft down

140 2,999

agairupdate

May 27

agairupdate

Mar 24

agairupdate

Jan 26

agairupdate

Dec 5

agairupdate

Dec 15

agairupdate

Dec 13

agairupdate

Dec 12

agairupdate

Dec 9

agairupdate

Dec 5

agairupdate

Nov 23

agairupdate

Nov 6

agairupdate

Nov 2

agairupdate

Oct 21

agairupdate

Oct 19

agairupdate

Oct 6

agairupdate

Oct 2

agairupdate

Sep 30

agairupdate

Sep 29

agairupdate

Sep 22

agairupdate

Sep 18